Get-NetUDPSetting
Gets UDP settings.
Syntax
Default (Default)
Get-NetUDPSetting
[[-DynamicPortRangeStartPort] <UInt16[]>]
[[-DynamicPortRangeNumberOfPorts] <UInt16[]>]
[-CimSession <CimSession[]>]
[-ThrottleLimit <Int32>]
[-AsJob]
[<CommonParameters>]
Description
The Get-NetUDPSetting cmdlet gets UDP settings for the IP interface. The cmdlet gets the starting port and the number of ports for a dynamic port range that the IP interface uses to send and receive UDP traffic. Use this cmdlet with the Set-NetUDPSetting to specify a dynamic port range to modify. If you do not specify any parameters, the cmdlet gets all dynamic port ranges for UDP from the IP interface.
Examples
Example 1: Get all dynamic port ranges for UDP
PS C:\>Get-NetUDPSetting
This command gets all UDP settings. The command gets all dynamic port ranges for UDP from the IP interface.
Parameters
-AsJob
Runs the cmdlet as a background job. Use this parameter to run commands that take a long time to complete.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-CimSession
Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.
Parameter properties
| Type: | CimSession[] |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | Session |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-DynamicPortRangeNumberOfPorts
Specifies an array of values for the number of ports for a dynamic port range that starts from the port that you specify for the DynamicPortRangeStartPort parameter. The cmdlet gets the UDP settings that have these values.
Parameter properties
| Type: | UInt16[] |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | 1 |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-DynamicPortRangeStartPort
Specifies an array of values for the starting port of the dynamic port range. The cmdlet gets the UDP settings that have these values. The acceptable values for this parameter are: 1 through 65535.
Parameter properties
| Type: | UInt16[] |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | 0 |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-ThrottleLimit
Specifies the maximum number of concurrent operations that can be established to run the cmdlet.
If this parameter is omitted or a value of 0 is entered, then Windows PowerShell® calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer.
The throttle limit applies only to the current cmdlet, not to the session or to the computer.
Parameter properties
| Type: | Int32 |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.
Inputs
None
Outputs
CimInstance
The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects.
The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.