Validate-OutboundConnector
This cmdlet is available only in the cloud-based service.
Use the Validate-OutboundConnector cmdlet to test the settings of Outbound connectors in Microsoft 365.
Note: This cmdlet does not set the validation status or timestamp on the connector. To set these values, run the following command: Set-OutboundConnector -Identity "<ConnectorName>" -IsValidated $true -LastValidationTimestamp (Get-Date).ToUniversalTime().
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Default (Default)
Validate-OutboundConnector
-Identity <OutboundConnectorIdParameter>
-Recipients <MultiValuedProperty>
[-Confirm]
[-WhatIf]
[<CommonParameters>]
Description
The Validate-OutboundConnector cmdlet performs two tests on the specified connector:
- SMTP connectivity to each smart host that's defined on the connector.
- Send test email messages to one or more recipients in the domain that's configured on the connector.
You need to be assigned permissions before you can run this cmdlet. Although this article lists all parameters for the cmdlet, you might not have access to some parameters if they aren't included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Validate-OutboundConnector -Identity "Contoso.com Outbound Connector" -Recipients laura@contoso.com,julia@contoso.com
This example tests the Outbound connector named Contoso.com Outbound Connector.
Parameters
-Confirm
Applicable: Exchange Online, Exchange Online Protection
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | cf |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Identity
Applicable: Exchange Online, Exchange Online Protection
The Identity parameter specifies the Outbound connector that you want to test. You can use any value that uniquely identifies the connector. For example:
- Name
- Distinguished name
- GUID
Parameter properties
| Type: | OutboundConnectorIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | True |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Recipients
Applicable: Exchange Online, Exchange Online Protection
The Recipients parameter specifies one or more email addresses to send a test message to. The email addresses need to be in the domain that's configured on the connector.
You can enter multiple values separated by commas. If the values contain spaces or otherwise require quotation marks, use the following syntax: "Value1","Value2",..."ValueN".
Parameter properties
| Type: | MultiValuedProperty |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | True |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-WhatIf
Applicable: Exchange Online, Exchange Online Protection
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | wi |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.