Start-DatabaseAvailabilityGroup
This cmdlet is available only in on-premises Exchange.
Use the Start-DatabaseAvailabilityGroup cmdlet to reincorporate one or more previously failed members of a database availability group (DAG).
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Identity
Start-DatabaseAvailabilityGroup
[-Identity] <DatabaseAvailabilityGroupIdParameter>
-ActiveDirectorySite <AdSiteIdParameter>
[-ConfigurationOnly]
[-Confirm]
[-DomainController <Fqdn>]
[-WhatIf]
[<CommonParameters>]
MailboxSet
Start-DatabaseAvailabilityGroup
[-Identity] <DatabaseAvailabilityGroupIdParameter>
-MailboxServer <MailboxServerIdParameter>
[-ConfigurationOnly]
[-Confirm]
[-DomainController <Fqdn>]
[-WhatIf]
[<CommonParameters>]
Description
The Start-DatabaseAvailabilityGroup cmdlet is used to activate DAG members in a recovered datacenter after a datacenter switchover, as part of the switchback process to the recovered datacenter. The Start-DatabaseAvailabilityGroup cmdlet manipulates configuration and state so that the servers are incorporated into the operating DAG, and joined to the DAG's underlying cluster. The Move-ActiveMailboxDatabase cmdlet is then used to activate databases in the primary datacenter.
You need to be assigned permissions before you can run this cmdlet. Although this article lists all parameters for the cmdlet, you might not have access to some parameters if they aren't included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Start-DatabaseAvailabilityGroup -Identity DAG1 -MailboxServer MBX2
This example starts the Mailbox server MBX2 in the DAG DAG1.
Example 2
Start-DatabaseAvailabilityGroup -Identity DAG1 -ActiveDirectorySite Redmond
This example starts the members of the DAG DAG1 in the Active Directory site Redmond.
Parameters
-ActiveDirectorySite
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The ActiveDirectorySite parameter specifies whether to start all DAG members in the specified site.
Parameter properties
| Type: | AdSiteIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
Identity
| Position: | Named |
| Mandatory: | True |
| Value from pipeline: | True |
| Value from pipeline by property name: | True |
| Value from remaining arguments: | False |
-ConfigurationOnly
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The ConfigurationOnly switch specifies whether to update the Active Directory properties with the start action, but doesn't perform a start of the DAG or any members. You don't need to specify a value with this switch.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Confirm
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | cf |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-DomainController
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
Parameter properties
| Type: | Fqdn |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Identity
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The Identity parameter specifies the name of the DAG being started.
Parameter properties
| Type: | DatabaseAvailabilityGroupIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | 1 |
| Mandatory: | True |
| Value from pipeline: | True |
| Value from pipeline by property name: | True |
| Value from remaining arguments: | False |
-MailboxServer
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The MailboxServer parameter specifies whether to start a single DAG member.
Parameter properties
| Type: | MailboxServerIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
MailboxSet
| Position: | Named |
| Mandatory: | True |
| Value from pipeline: | True |
| Value from pipeline by property name: | True |
| Value from remaining arguments: | False |
-WhatIf
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Server SE
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | wi |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.