Remove-UMIPGateway
This cmdlet is available only in on-premises Exchange.
Use the Remove-UMIPGateway cmdlet to delete a Unified Messaging (UM) IP gateway.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Default (Default)
Remove-UMIPGateway
[-Identity] <UMIPGatewayIdParameter>
[-Confirm]
[-DomainController <Fqdn>]
[-WhatIf]
[<CommonParameters>]
Description
The Remove-UMIPGateway cmdlet deletes a specified UM IP gateway. After the UM IP gateway is deleted, Mailbox servers no longer accept new call requests from the IP gateway.
The Remove-UMIPGateway cmdlet should be run only by an administrator who fully understands the implications of disabling communication with a Session Initiation Protocol (SIP)-enabled IP Private Branch eXchange (PBX) or IP gateway.
After this task is completed, the UM IP gateway is removed from Active Directory.
You need to be assigned permissions before you can run this cmdlet. Although this article lists all parameters for the cmdlet, you might not have access to some parameters if they aren't included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Remove-UMIPGateway -Identity MyUMIPGateway
This example deletes the UM IP gateway MyUMIPGateway.
Parameters
-Confirm
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | cf |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-DomainController
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
Parameter properties
| Type: | Fqdn |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Identity
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
The Identity parameter specifies the identifier for the UM IP gateway being deleted.
Parameter properties
| Type: | UMIPGatewayIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | 1 |
| Mandatory: | True |
| Value from pipeline: | True |
| Value from pipeline by property name: | True |
| Value from remaining arguments: | False |
-WhatIf
Applicable: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | wi |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.