New-RpcClientAccess
This cmdlet is available only in Exchange Server 2010.
Use the New-RpcClientAccess cmdlet to create configuration information for the Exchange RPC Client Access service on a Client Access server. This set up task is performed by default on new installations of the Client Access server role on Microsoft Exchange Server 2010.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Default (Default)
New-RpcClientAccess
-Server <ServerIdParameter>
[-BlockedClientVersions <String>]
[-Confirm]
[-DomainController <Fqdn>]
[-EncryptionRequired <Boolean>]
[-MaximumConnections <Int32>]
[-WhatIf]
[<CommonParameters>]
Description
After you run this command, you must start the Exchange RPC Client Access service on the Exchange Client Access server to enable RPC client access.
You need to be assigned permissions before you can run this cmdlet. Although this article lists all parameters for the cmdlet, you might not have access to some parameters if they aren't included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
New-RpcClientAccess -Server CAS01
This example creates configuration information for the Exchange RPC Client Access service on the Client Access server CAS01. After you run this command, you must start the Exchange RPC Client Access service on the Exchange Client Access server to enable RPC client access.
Parameters
-BlockedClientVersions
Applicable: Exchange Server 2010
The BlockedClientVersions parameter specifies which versions of Microsoft Outlook are restricted from connecting. The Exchange RPC Client Access service rejects Outlook connections if versions are in the range specified. This setting affects MAPI and Outlook Anywhere client connections. The value must be less than 256 characters in length.
Versions should be single numbers in the format X.Y.Z where X is a major version number, Y is the minor revision number, and Z specifies the build, and ranges should be delimited by semicolons (for example, 0.0.0-5.9.9; 7.0.0-65535.65535.65535).
Parameter properties
| Type: | String |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Confirm
Applicable: Exchange Server 2010
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | cf |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-DomainController
Applicable: Exchange Server 2010
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
Parameter properties
| Type: | Fqdn |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-EncryptionRequired
Applicable: Exchange Server 2010
The EncryptionRequired parameter specifies whether to require Outlook connections to be encrypted. The Exchange RPC Client Access service rejects unencrypted Outlook connections if this parameter is set to $true.
Parameter properties
| Type: | Boolean |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-MaximumConnections
Applicable: Exchange Server 2010
The MaximumConnections parameter specifies the maximum number of concurrent connections allowed. The Exchange RPC Client Access service reads and limits connections based on this property.
This parameter has a range from 1 through 65535.
Although you can configure a non-default value for this parameter, changes to this setting aren't enforced in this version of Exchange.
Parameter properties
| Type: | Int32 |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
-Server
Applicable: Exchange Server 2010
The Server parameter specifies the Client Access server where you want to run this command. You can use any value that uniquely identifies the server. For example:
- Name
- FQDN
- Distinguished name (DN)
- ExchangeLegacyDN
Parameter properties
| Type: | ServerIdParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | True |
| Value from pipeline: | True |
| Value from pipeline by property name: | True |
| Value from remaining arguments: | False |
-WhatIf
Applicable: Exchange Server 2010
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
Parameter properties
| Type: | SwitchParameter |
| Default value: | None |
| Supports wildcards: | False |
| DontShow: | False |
| Aliases: | wi |
Parameter sets
(All)
| Position: | Named |
| Mandatory: | False |
| Value from pipeline: | False |
| Value from pipeline by property name: | False |
| Value from remaining arguments: | False |
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.